Looking to finally make the jump from my old Ender 3 to a better printer, I’ve upgraded the Ender quite a lot but have run into multiple problems over the years with custom firmwares. During my last move, I snapped the SD card slot off the main board and have had issues getting the new one back up and running. With all of that said I’m ready to just buy once, cry once, and get back to printing.
The options I’m looking at are either the X1C or the P1S. I wanted to get opinions here, as from what I’ve found so far, the P1S seems to have the same print speed/quality, just minus the AI, and upgraded steel components. How capable is the P1S stock, and what upgrades, if any, would be recommended?
From what I’ve found, the AMS 2 seems to be the ideal choice over the OG AMS due to the drying function and more user-friendly design. It’s $120 more for the AMS 2 combo than the AMS combo, so for those of you who have these setups, is the AMS 2 worth it?
Other than the printer selection, what are your go-to filaments and brands? I’ve seen PPA-CF, PA6-CF, and PAHT-CF mentioned, but don’t really understand the pros and cons of each.
I was a long-time lurker on the Fosscad sub, but I am hoping to contribute moving forward.
Elegoo Centauri Carbon, it’s half the price of p1s, can print nylon out of the box as it comes with a hardened hotend, and has an enclosure for $299.99
Neither. Get a centauri carbon or anycubic Kobra s1. Bambu labs ain’t bambu-ing like it used to for the money they ask
I’m actually in the position of having used both an X1C and a P1S.
The TL;DR:
- The P1S has a 1Hz(!) refresh rate camera whereas the X1C does 24 or 30 or whatever
- The X1C does automatic flow rate calibration via the LIDAR sensor not present on the P1S
- The X1C can have x1plus flashed to it, which allows finer control over the printer and, more importantly, optimizes its pre-print calibration sequence down to about half the usual time. There is no equivalent for the P1S.
Are those differences worth like $400? Up to you.
I just got an x1c this last week, what should I do? Been using it and liking it. I plan to get a longer cable for the ams, maybe get some filtration setup but what I mean is whats a good setup that also is privacy focused. I have it in Lan mode atm. Can I connect it to orca slicer while preserving privacy. Is it possible to view the IP cam on my phone in a privacy centered setup? I was thinking about trying the custom firmware route for sure just haven’t got around to it yet.
LAN mode is fine, but I don’t think there’s a way to get Bambu Handy to play nicely with it, no. But in LAN mode, it should be safe to connect to it via Orca – that traffic doesn’t leave your LAN, last someone sniffed it with wireshark.
It’s not an entry-level setup by any fucking means, but what I’ve got is my Bambu hooked up to HomeAssistant, which proxies the webcam and lets me view it from my phone along with all of its instrumentation. That plus some HA automations to message me on Matrix when the printer starts, stops, has an error, etc.
x1plus is good. I don’t use any of its niche features, just like the peace of mind and the quicker pre-print calibration.
P1S for me: all I did was swap to a hardened steel nozzle+gears, installed voxelpla detached motion feet instead of the solid rubber pads, switched to lan mode, and got a couple build plates from darkmoon(satin/cfx). I have a separate hs nozzle I wired a 33ohm resistor in-line to up nozzle temps as well, just haven’t installed it yet. I print from a polydryer with the printed 5% air exchanger mod+mesh plastic upgraded to SS window screen on the dryer, so I cant speak for the ams/2. Fiberon pa6/pet/pps
Any recommendations on the nozzle and gears? Also, is there a reason to get both the satin and cfx build plates if the cfx can handle the long range of filament types?
I upgraded the gears with HS simultaneously with the high temp modded HS nozzle install, all bambu official parts
